More information is available at Plumb2u.
Eugenio Canipe
0
25
09.22 10:10
Before placing an order, it pays to note three things on site: whether the cistern sits flush to the pan or is wall-mounted above it, the fill valve's body length if there is a tight fit inside the tank, and whether the existing lever operates through the lid or via an external arm. Plumb2U carries fill valves, flush valves and levers suited to both close-coupled and low-level cisterns, stocked at trade prices for plumbers who need to get the right part on the first order rather than the second. Trade supplies despatch from Plumb2U's Epsom base to plumbers across the UK, and Plumb2U remains a straightforward call when the cistern type is not obvious from the pan alone.
Before ordering, it helps to note the frame's brand if it is visible on the tank or access panel, along with the fill valve and flush valve dimensions if the old parts can be measured before removal. Plumb2U stocks fill valves, flush valves, cables, spindles and flush plates suited to the concealed cisterns most commonly found in UK homes, at trade prices, which helps when a plumber is working blind on a job where the tank itself cannot be seen until the access plate is off. With next-day despatch available on the common models, Plumb2U's stock list is worth checking against the frame details before committing to a specific part.
More information is available at trade plumbing supplies.
A close-coupled cistern bolts directly onto the back of the pan with no visible pipework between the two. Because the outlet on the cistern base sits directly above the inlet on the pan, the flush valve or siphon needs a shorter outlet and often a rubber doughnut washer to seal the joint rather than a length of pipe. Fill valves on close-coupled units tend to be shorter in the body too, since there is less depth inside a compact tank.
Start with the fill valve. This is the mechanism that lets water into the cistern after a flush and shuts off once the tank reaches the correct level, usually via a float or a diaphragm. When a fill valve wears, the most common signs are a hissing or trickling noise that continues long after the cistern should have stopped filling, a water level creeping up to or past the overflow pipe, or a float arm that no longer rises high enough to trigger shut-off. Mineral deposits inside the valve seat are often the culprit, particularly in hard water areas, and once the seal degrades a full replacement is usually more reliable than trying to clean it out.
When a full lever replacement is needed, the fitting type has to match what is already there. Side levers, which mount through a hole in the side of the cistern, come in different thread diameters and in both metal and plastic bodies, and the arm length inside the tank needs to reach the flush valve or siphon without fouling the tank wall. Levers that mount through the lid, more common on close-coupled and concealed designs, connect via a spindle rather than a side arm and are not interchangeable with side-lever fittings.
Before ordering, it helps to note the frame's brand if it is visible on the tank or access panel, along with the fill valve and flush valve dimensions if the old parts can be measured before removal. Plumb2U stocks fill valves, flush valves, cables, spindles and flush plates suited to the concealed cisterns most commonly found in UK homes, at trade prices, which helps when a plumber is working blind on a job where the tank itself cannot be seen until the access plate is off. With next-day despatch available on the common models, Plumb2U's stock list is worth checking against the frame details before committing to a specific part.
More information is available at trade plumbing supplies.
A close-coupled cistern bolts directly onto the back of the pan with no visible pipework between the two. Because the outlet on the cistern base sits directly above the inlet on the pan, the flush valve or siphon needs a shorter outlet and often a rubber doughnut washer to seal the joint rather than a length of pipe. Fill valves on close-coupled units tend to be shorter in the body too, since there is less depth inside a compact tank.
Start with the fill valve. This is the mechanism that lets water into the cistern after a flush and shuts off once the tank reaches the correct level, usually via a float or a diaphragm. When a fill valve wears, the most common signs are a hissing or trickling noise that continues long after the cistern should have stopped filling, a water level creeping up to or past the overflow pipe, or a float arm that no longer rises high enough to trigger shut-off. Mineral deposits inside the valve seat are often the culprit, particularly in hard water areas, and once the seal degrades a full replacement is usually more reliable than trying to clean it out.
When a full lever replacement is needed, the fitting type has to match what is already there. Side levers, which mount through a hole in the side of the cistern, come in different thread diameters and in both metal and plastic bodies, and the arm length inside the tank needs to reach the flush valve or siphon without fouling the tank wall. Levers that mount through the lid, more common on close-coupled and concealed designs, connect via a spindle rather than a side arm and are not interchangeable with side-lever fittings.
공지
